Automatic soy processing plant from fabricator

Specifications

soy processing plant
1. Engineer group
2. Supply turnkey project
3. ISO, CE, BV
4. Long service life

Automatic soy processing plant from fabricator

WHAT MACHINES WILL BE USED IN OIL PLANT?

Pretreatment section:

Solvent extraction section:

BRIEF INTRODUCTION OF PRETREATMENT:

1.Screening: Removing the chaff and broken rice in the rice bran, in case of they will influence

the oil yield and the desolvent of wet meal in the next process. In the process of puffing section,

the general requirement of impurity is less than 3%, and the requirement of crude fiber is about 8%.

2.Magnetic separation: Clearing the iron impurity which might be in the rice brain. Since in the

process of puffing, the iron impurity will be harmful to the screw of extrusion machine, affect

the puffing effect. As the rice brain particles are small and poor liquidity, the iron impurities are always be wiped off by the magnetic barrels installed in the feeding port.

3.Quenching and tempering: it is the process of preheating so that to improve the temperature

of the rice bran before puffing. After quenching and tempering the temperature will be controlled at 65--75 °C, and the moisture will be controlled at 10 ~12%. Thus, on the one side, it can

increase the output of the extrusion machine, and on the other side, it can improve the quality of the puffed rice bran.

4. Puffing the rice bran is injecting high pressure steam and high temperature water through the

extrusion machine, so that it can improve the temperature and moisture in the extrusion machine,and can also form the high pressure to process the rice bran. All these can make the the rice bran become porous columnar structure from the original pulverized state.

All these effectively passivate the activity of various of enzyme in the rice bran, and destroy

the fat layer structure, so that it will be easier for the oil yield.

5.Drying: The moisture of puffed material comes from the extrusion machine is too big and the

temperature is too high for direct leaching, the must be experience to process of drying and coo-ling, thus the moisture will reach 7%--9%, and temperature will reach 50--55°C. After puffing, the rice brain are usually dried and cooled by plat dryer.

SOLVENT EXTRACTION PROCESS:

First, send the rice bran meal to the roary extractor, the meal will be fully soaked in the extractor by the solvent. Thus, the oil in the rice bran will be absorbed in to the solvent.

1. Solvent pumps: continuously spray solvent to the rotary-type extractor

2.Roary extractor: Spray and soak the pretreatment rice brain with solvent so that oil fats can be dissolved in solvent(form miscella). After processing, you can get wet meal and miscella (mixed oil) .

3. LD: usd to separate the solvent from the wet meal.

4. Miscella tank 1st: pump the miscella (oil with solvent) in to the miscella 1st , and then add 10% saline water to it. The phospholipid and impurities in the miscella will react with the saline wter, at last the reactant precipitate, reaching the goal of purifying.

5. Miscella tank 2nd: the purified miscella will be pumped into it.

6. 1st evaporator, 2nd evaporator: used to separate the solvent from the oil. After this process,

the solvent can be removed 85%.

7. Miscella stripping: it will remove the remaining solvent in miscella. And the solvent will be

discharged to condenser for recycling.

8. condensers: used to cooling the solvent gas separated from the wet meal and miscella for recycling.

WHAT CERTIFICATES DO WE HAVE?

Still have questions?

What should you do??

Do not worry!

SAM is always here!!

Just knock me!!!

Oil refining means separating impurity from oil based on the different characteristics of oil and impurity, in order to enhance the stability and security of oil. Oil refining including two technologies, physical refining and chemical refining.echnological process details of Automatic soy processing plant from fabricator:
AAA1

1. Acid reaction process
Oil temperature can be adjusted by screw plate heat exchanger. When the temperature is heated to about 80℃, mixing about 85% food grade phosphoric acid into acid reaction tank for reacting. In the tank, most non-hydrated phospholipid transfer into hydrated phospholipid.
AAA1

2. Neutralization process
In the neutral section, degummed oil with appropriate temperature and the appropriate concentration of alkali liquor, into the neutralization centrifugal mixer mixing, in order to achieve the effect of mixed, the mixture is then sent to neutralization tank for enough time, in this process, excessive alkali neutralization of free fatty acids and some phosphate form soapstock , after pumping oil soap mixture into heater oil heating to 85 ~ 90 ℃ in centrifuge separation oil - soap (or oil - glue). Oil soapstock of the separated (or foot) feet into the oil tank, and then to the salting out with soap pump tank isolated part of the oil.
AAA2

3. Washing process
Neutral oil from separator, still contains about 500 ppm soap, in order to reduce the residual content of soap, oil is joined by about 10% of hot water, washed in the washing mixer, hot water will absorb oil soap and other impurities, then in the water separator are separated.

AAA3

If you have any demand about microwave drying equipment and edible oil refining equipment, pls feel free contact us any time.

LD Miss Candy
Skype: leaderfoodmachine9
Mobile: +86 18363700691 (Also WhatsApp & Wechat)
Email: [email protected]

Shandong Leader Machinery Co.,ltd. is a microwave equipment, microwave drying sterilization machine, microwave heating equipment, microwave drying machine, microwave sterilization equipment, microwave drying equipment, whole s microwave curing equipment, microwave drying sterilization condiment, Shandong microwave drying Machine, melon seeds microwave dryer and other products specializing in the production and processing company, has a complete and scientific quality management system. Shandong Leader Machinery Co.,ltd.integrity, strength and quality of products recognized by the industry.

Why do you choose the Shandong Leader Machinery Co.,ltd. Automatic soy processing plant from fabricator?
1.Healthy! Pure mechanical squeezing craft maximally keeps the nutrients of the oil plants.No chemical substances left
2. High working efficiency! Due to a high working efficiency of the screw oil press machinery,both time and power can be saved.
3. Long durability! All the parts are made of the most suitable material and treated with refined crafts, such as cemented quenching and tempering to increase the hardness, consequently the durability.
4. Automatic soy processing plant from fabricatorCost-effective! Low investment! The wearing parts on the oil press machinery such as the squeeze loop, squeeze spiral and squeeze bar are designed to be dismountable. When they are out of service period, users only need to replace them and there is no need to displace the whole machine.

Shandong Leader Machinery Co.,Ltd.
Tel:+86 0531 85064681
Fax:+ 86 0531 85064682
Skype： taishan0072
What’sApp:+86 18905316466
Email: [email protected]

Address: No. 225, Huangqiao Village, Beiyuan, Tianqiao District, Jinan, Shandong, China

 

 

 

At Shandong Leader Machinery Co.,Ltd, we have one single goal in mind: to make you a satisfied customer. That single focus, driven from every aspect of the company's operation, is the key to our ongoing success. If you're a satisfied customer, you'll come back to us when you have additional Machine needs in the future, and you'll tell your friends about us. Then if we can make them satisfied customers, the cycle continues.

——————————————————————Wendy Yao Director